Nowadays, we can see various forms and colorful aluminum veneer curtain wall projects in large cities and small towns. In order to make China's high-rise buildings more bright and gorgeous, a curtain wall pattern composed of a variety of colors and materials is formed. The overall shape of hyperbolic aluminum veneer curtain wall is pear shaped. It is made of 2.5-thick aluminum veneer. The size of the panel is the same as the size of the head. After disassembly, it is found that the effect is not very good, the whole wall is uneven, there are obvious reflection traces, and the panel surface is uneven. It is helpful to analyze the causes and how to do similar projects. Now, let's see what the problem is!

1. Possible installation problems with poor site effect, including installation adjustment and site installation quality considered by the system.

2. The first aluminum plate is too thin or the reinforcing rib is unreasonable, resulting in insufficient structural performance, environmental and aesthetic performance of the aluminum plate

Defects of secondary support system, adjustment of horizontal frame and error of main structure

The third problem is in the construction process, which is a variety of problems

The fourth problem is that article 4 has a lot to do with the company.

The fifth part of the connection problem is usually found in this link

I have made many hyperbolic stainless steel plates, aluminum plates, metal roof glass, etc. from my perspective, your effect is very good.

3. The first is a reasonable power grid, and the other is the production level of aluminum deep processing units.

4. Technical problem: the deformation of the stressed part is too obvious and the aluminum plate is thin.

5. Do a good job. Only modular splicing is allowed. Each plate is an independent and non interchangeable forming surface. In the formed plate, it can be interchanged after being fixed with a fixed bracket. The size is fixed and matched with the wall keel. The packaging shall not be deformed during transportation and processing. Please do not touch the front of the molded part when installing the support, and do not press the mold surface with force. It has not changed. It's better in the front.

The whole installation is completed and packaged from top to bottom.

I don't make aluminum, but I think it's ok if I do. When installing the wall, it was fixed on the bracket before fixing the wall, which caused a large amount of deformation. The deformation range can be controlled to the minimum. After all, the accuracy of factory debugging is much higher than that of on-site debugging.

Of course, this will increase the cost of installation, rear support module, transportation and packaging. But every penny counts. This is a good job, not money.

6. Possible installation problems, including system installation and adjustment, on-site installation quality,

7. For possible installation problems, system installation and adjustment shall be considered, and on-site installation quality control shall be carried out.

One of the reasons for this estimation is that the force is not uniform when the plate is bent.

8. For various reasons, the effect of manual installation of hyperbolic surface and flat plate components is inevitable. After all, maps are not good on computers.

First, when you say hyperbola, you mean hyperbola in the whole shape.

However, the aluminum plate you use is actually a flat plate. Therefore, since your aluminum plate is not hyperbolic, that is, the plate is combined into a hyperbolic shape,

You can consider this effect first. If the radius of the hyperbola is large enough, the length of the arc is the same as the length of the chord of the veneer (that is, basically close), and the assembly effect is better. Otherwise, the veneer is best treated with hyperbola.

Secondly, in the process of aluminum plate processing, the arrangement of reinforcement and the processing control of deformation, especially the edge position. The second is to control the color difference of aluminum surface coating.

Third, in the process of aluminum plate installation, workers should install quality control devices. The aluminum plate must not be damaged. Of course, do not carry out any secondary processing, and it is best to avoid secondary processing. Special attention shall be paid to leveling control during installation.

The fourth is the installation quality control of the framework. Generally speaking, the design can basically meet the requirements, which is very important in the field installation quality control. The color of aluminum is also important. Especially when aluminum plates are used in a large area. look out. I think you did a good job.

Building aluminum veneer, aluminum square and embedded part of glass curtain wall facade are important components of curtain wall. Its main function is to transfer the load and effect of aluminum curtain wall site